CF200-A12C 200 watt high density ac/dc power supply CF200-A12C.a01 page 1 of 4 technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232 www.murata-ps.com features 200w compact high density active load current share universal ac input with power factor correction ruggedized u-channel construction rohs compliant includes oring diode for n+1 parallel operation international regulatory approvals description the CF200-A12C switching power supply utilizes advanced component and circuit technologies to deliver one of the industrys smallest 200 watt switchers. built to meet 1u height considerations, the u-frame package measures only 3.30 x 5.00 x 1.50. the CF200-A12C offers universal ac input (85-265vac) with active power factor correction (pfc) and compliance to worldwide safety and emc standards. selection guide model number power output main output auxilliary output CF200-A12C 200w 12v 5v input characteristics parameter conditions min. typ. max. units input voltage operating range 85 264 vac input frequency 47 63 hz turn-on input voltage ramp up 75 vac turn-off input voltage ramp down 65 maximum rated input current 100vac 2.8 arms inrush current cold start at 25c, 115vac 25 apk cold start at 25c, 230vac 50 power factor 230vac, full load 96 % 115vac, full load 98 output voltage characteristics output voltage parameter conditions min. typ. max. units 12v voltage set point accuracy 1% tolerance 12.2 vdc line and load regulation 1 % ripple voltage & noise 1 20mhz bandwidth 150 mv p-p output current 0 16.6 a peak current 17 5vaux voltage set point accuracy 5 vdc line and load regulation 2 % output current 0 5 ma ripple voltage & noise 1 20mhz bandwidth 100 mv p-p output characteristics parameter conditions min. typ. max. units remote sense compensates for voltage drops of up to 0.5v between the power supply to the load. outputs are internally sensed at output connector if remote sense lines are opened. ef?ciency 230vac, full load 86 % 115vac, full load 82 start-up delay output voltage at 90% 2.0 s rise time 20 ms transient load response for load change of 25% to 75%, at slew rate of 1a/s, recovery time less than 2ms 5 % current sharing accuracy single wire current share in a n+1 parallel redundant con?guration with or-ng diodes included in the psu 10 % hot swap available hold-up time 110vac, full load 16 ms overshoot and undershoot voltage change at turn-on and turn-off 1 % 1 ripple and noise are measured with 10 f, in parallel with 0.1 f ceramic capacitors.
technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232 www.murata-ps.com CF200-A12C 200 watt high density ac/dc power supply CF200-A12C.a01 page 2 of 4 general characteristics parameter conditions min. typ. max. units storage temperature range non-condensing -25 85 c operating temperature range derating linearly to 70c at -2.5% per 1c -5 50 temperature coef?cient 0.02%/c 0 70 cooling 100w free convection cooling (base plate cooling). 200w continuous forced air cooling, 15cfm min. operating humidity non-condensing 5 95 % storage humidity non-condensing 5 90 altitude operating 10,000 ft. non- operating 40,000 ft. vibration three orthoganol axes at 1octave/min, 5 min dwell at four major resonances at 0.75g peak, 5hz to 500hz mtbf calculated per bellcore 332, issue 6 speci?cation at ta=30c (max junction temperature for silicon 110c, capacitors 105c 300 khrs safety approvals ul 60950, csa c22.2-234, level 3, en-60950-1, ce-mark input fuse power supply has internal line fuse: iec type 4a 250vac normal blo switching frequency 85 90 khz weight 510g protection characteristics parameter conditions min. typ. max. units over temperature internal thermostat protects the power supply against excessive temperature. automatic recovery. over voltage outputs shut down at 125% of nominal; ac input must be recycled to restore operation. over current 12v output: 110 to 130% of imax, hiccup mode current limit; automatic recovery. long-term fail condition shall not cause damage to psu. isolation characteristics parameter conditions min. typ. max. units insulation safety rating / test voltage input to output - reinforced 3000 vrms input to chassis - basic 1500 vrms isolation output to chassis 100 vdc material flammability ul 94v-0 grounding output rtns not connected to chassis gnd. 12v rtn and 5v rtn shorted. control signals status description power good (pg) indication this signal is used to detect the presence of output voltage. this signal goes high when input power is applied and output volt age is more than 85% of nominal 12.0 vdc output. signal type: ttl-compatible, with 2.43k pull-up resistor to +5v. enable active low input to enable +12vdc output of power supply. +sense positive side of remote sense input. -sense negative side of remote sense input. 5v aux +5v standby. current share single-wire current-share connection. led drive 10ma min. when pg is high, pin 1 of j2 shall go high to illuminate external green led. when pg is low, pin 3 of j2 shall go h igh to illuminate external yellow led.
technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232 www.murata-ps.com CF200-A12C 200 watt high density ac/dc power supply CF200-A12C.a01 page 3 of 4 output connector and signal specification pin j1 : molex 26-48-1055 pin j6 : molex 26-60-4100 1 chassis 1 +12v/rtn 3 neutral 2 +12v/rtn 5 phase 3 +12v/rtn 4 +12v/rtn pin j2 : led (mating connector optional) 5 +12v/rtn 1 dc ok led 6 +12v 2 common led 7 +12v 3 dc fail led 8 +12v 9 +12v pin j3, j4 : fan (mating connector optional) 10 +12v 1 +12v 2 +12v rtn 3 fan fail signal pin j5 : amp 640456-8 1 power good (pg) low 2 enable, active high (for normal operation, short to - sense) 3 + sense 4 - sense 5 5v standby 6 c.s. 7 fan 1 fail signal to j3-3 8 fan 2 fail signal to j4-3 emissions and immunity characteristic description criteria harmonics iec/en 61000-3-2 voltage fluctuation and flicker iec/en 61000-3-3 emission conducted fcc / en55022 (cispr 22) class b, 6 db margin C with an external line ?lter type 03ss-p-q by high lan or equivalent esd iec/en 61000-4-2 4kv contact discharge, performance criteria b 8kv operational air discharge, performance criteria b. electromagnetic field iec/en 61000-4-3 electrical fast transients/burst iec/en 61000-4-4 1kv for ac power port, 0.5kv for dc power i/o and signals port, performance criteria b surge iec/en 61000-4-5 1kv differential mode and 2kv common mode rf conducted immunity iec/en 61000-4-6 3 vac, 80% am, 0.08-1khz, performance criteria a magnetic immunity iec/en 61000-4-8 3 a/m at 50hz, performance criteria a voltage dips, interruptions iec/en 61000-4-11 20% reduction for 10ms - criteria b, 60% for 100ms - criteria c, 90% reduction for 5000ms - criteria c.
technical enquiries email: toronto@murata-ps.com, tel: +1 (866) 740 1232 www.murata-ps.com CF200-A12C 200 watt high density ac/dc power supply CF200-A12C.a01 page 4 of 4 mechanical dimensions dimensions: 127mm x 84mm x 39.6mm mating connectors connector housing crimp terminal j1 molex 09-50-3051 (1x) molex 08-52-0113 (3x) j2, j3, j4 amp 1375820-3 (1x) amp 1375819-1 (3x) j5 amp 1375820-8 (1x) amp 1375819-1 (8x) j6 molex 09-50-3101 (1x) molex 08-52-0113 (10x) 1 3 places amp 640456-3 fan2 j3 fan1 1 1 j4 j2 1 led j5 molex 26-48-1055 0 input j1 1 j6 57.15 33.10 13.34 117.00 c l 8.26 127.00 109.22 signaling amp 640456-8 1 +12v output molex 26-60-4100 side mounting holes (m3, 4 places) 38.10 83.82 (m3, 4 places) mounting holes max. compnent height 39.60 09/07/08 murata power solutions, inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. the descriptions contained her ein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. speci?cations are subject to chan ge without notice. ? 2008 murata power solutions, inc. usa: mans?eld (ma), tel: (508) 339-3000, email: sales@murata-ps.com canada: toronto, tel: (866) 740-1232, email: toronto@murata-ps.com uk: milton keynes, tel: +44 (0)1908 615232, email: mk@murata-ps.com france: montigny le bretonneux, tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com germany: mnchen, tel: +49 (0)89-544334-0, email: munich@murata-ps.com japan: tokyo, tel: 3-3779-1031, email: sales_tokyo@murata-ps.com osaka, tel: 6-6354-2025, email: sales_osaka@murata-ps.com china: shanghai, tel: +86 215 027 3678, email: shanghai@murata-ps.com guangzhou, tel: +86 208 221 8066, email: guangzhou@murata-ps.com singapore: parkway centre, tel: +65 6348 9096, email: singapore@murata-ps.com murata power solutions, inc. 11 cabot boulevard, mans?eld, ma 02048-1151 u.s.a. tel: (508) 339-3000 (800) 233-2765 fax: (508) 339-6356 www.murata-ps.com email: sales@murata-ps.com iso 9001 registered
|
